Other

Our spray kit includes the 2:1 Pogo Plus Bung Mount Piston Stainless Steel Pump, 25 foot hose and the Model 2001 Stainless Steel Spray Gun with all hardware included. All you will need to apply wat...

Our spray kit includes the 2:1 Pogo Plus Bung Mount Piston Stainless Steel Pump, 25 foot hose and the Model 2001 Stainless Steel Spray Gun with all hardware included. All you will need to apply wat...

Hang Four Fabricator allows you to fabricate a wide variety of wall achors, braces, hangers and more…on the job. It punches, bends, twists and cuts to your specifications with no more costly delays.

Tinner’s molds to make copper parts. 800-753-0393 or email us. These fit a Chicago Dreis & Krump Model 818 Handbrake. Two (2) Sets available, MAKE A SERIOUS CA$H OFFER. One set is still in the orig...

DORAN Model PH-01001 Pistol Grip Air Hammer Best suited for floor mounted compressors. Weight: 5Lbs Can run on air pressures from 30 to 100 PSI. Running constantly at 30PSI it uses only 3.5CFM, at...

(Includes ONE SET – 3/8″ Single Bead Rolls) - 11″ Throat Depth - 14 Gauge Mild Steel Beading Capacity - Based on a standard set of rolls, top speed is 87 RPM which equates to 73.25 surface feet per...

This is actually a NEW machine we have here for demos. It’s available as it is, with the roll sets we have with it, Ogee, Elbow and others. It’s wired 110-volt, but we can easily get you one wired ...

This machine is designed for heavy gauge Pittsburgh locks. Complete with hardened feed gauge, 3 piece roll/shaft/gear construction, and calibrated dial for 16-20 Ga. mild steel. Specifications: Ca...

This NEW Flagler 20-Gauge Standard Pittsburgh Machine is IN STOCK and is ideal for small to medium sized sheet metal contractors or for fitting departments of large manufactures. This machine feat...

The 24-gauge Portable Pittsburgh rollformer is ideal for small to medium sized sheet metal contractors or jobsite manufacturing. Photo above shows the rollformer with the optional Flanging Attachme...

Lockformer Pittsburgh Lock Roll Former | Model 16 The Pittsburgh lock revolutionized the HVAC industry in the late 1940’s and is still used today for its strength and ease in assembling ductwork. A...

Lockformer Galv-Off Galvanize Cleaner There is simply no better product to soften and dissolve galvanize build-up on forming rolls and press dies than Lockformer Galv-Off Galvanize Cleaner. Galv-Of...

The 5400 Hammer shown is the EXACT HAMMER you will receive, the BRAND NEW Handle is included, but not shown in this photo. This hammer speeds up and takes the work out of the only tedious, costly, ...

This is a 18-gauge Pittsburgh equipped with the Right Angle flange rolls giving you both rolls to form a 18-ga Pittsburgh lock. Ready to ship, call us or email us using the form below. 800-753-0393...

The unit comes with a 1/2 H.P. electric motor, 115/208-230V, 5.4 AMPS 60 cycle single phase. We use Torrington Needle Bearings and hardened steel components throughout, 62 Rockwell. This unit featu...

The unit comes with a 1/2 H.P. electric motor, 115/208-230V, 5.4 AMPS 60 cycle single phase. We use Torrington Needle Bearings and hardened steel components throughout, 62 Rockwell. The cabinet and...

The Stand Alone Perforation Machine is ideal to perforate your metal for Ridge Cap venting and Soffit area venting. It can accept up to 24” wide sheet stock in 24 – 26 ga. Steel, .032” Aluminum, a...

Handbrake stands for 4' and smaller brakes. We have them in stock for Tennsmith or Roper Whitney or any brake for that matter. BETTER THAN FACTORY & FACTORY STANDS IN STOCK! 800-753-0393

PLASMA CUTTER We can provide every piece of equipment to form up TDC or TDF duct. You will probably want to have all of the components shown above as well as a brake to bend up the flanged duct. T...